Weslo compact SL User Manual

USER'S MANUALSerialNumberDecalModel No. WETL30708.0Serial No.CAUTIONRead all precautions and instruc-tions in this manual before usingthis equipm

107. Have a second person lift and hold the Frame(67) until step 8 is completed.Next, place the cylinder end of the Gas Spring(1) near the bracket on

119. Identify the Right Handrail Cover (95) and theLeft Handrail Cover (93). Slide the end of theRight Handrail (94) through the hole in the RightHand

1211. Attach the Right Handrail (94) to the Console(52) with an M5 x 16mm Screw (13), an M5 StarWasher (12), and two M4.2 x 19mm Screws(10). Make sure

1313. Attach the Console (52) to the Uprights (96, 98)with six M8 x 16mm Bolts (17) and six 5/16" StarWashers (2). Start all six Bolts before tig

1417. Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware maybe included. Keep the included hex keys in

15THE PRE-LUBRICATED WALKING BELTYour treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply sili-cone spray

16FEATURES OF THE CONSOLEThe treadmill console offers a selection of featuresdesigned to make your workouts more effective. Whenyou select the manual

17HOW TO TURN ON THE POWERIMPORTANT: If the treadmill has been exposed tocold temperatures, allow it to warm to room tem-perature before turning on th

184. Follow your progress with the displays.The lower leftdisplay—As you exer-cise, the lower left dis-play can show theelapsed time and thedistance t

19HOW TO USE A SPEED WORKOUT1. Insert the key into the console.See HOW TO TURN ON THE POWER on page17.2. Select one of the four speed workouts.To sele

2WESLO is a registered trademark of ICON IP, Inc.WARNING DECAL PLACEMENTThis drawing shows the location(s) of the warningdecal(s). If a decal is missi

HOW TO FOLD AND MOVE THE TREADMILLHOW TO FOLD THE TREADMILL FOR STORAGERemove the key and unplug the power cord. CAUTION:You must be able to safely li

21HOW TO LOWER THE TREADMILL FOR USE1. Hold the treadmill with your right hand as shown. Pull thelatch knob to the left and hold it. Pivot the frame d

22TROUBLESHOOTINGMost treadmill problems can be solved by following the steps below. Find the symptom that applies, andfollow the steps listed. If fur

23Locate the Reed Switch (55) and the Magnet (49)on the left side of the Pulley (58). Turn the Pulleyuntil the Magnet is aligned with the Reed Switch.

24PROBLEM: The walking belt is off-center or slips when walked onSOLUTION: a. If the walking belt is off-center, first remove the keyand UNPLUG THE PO

25These guidelines will help you to plan your exerciseprogram. For detailed exercise information, obtain areputable book or consult your physician. Re

26PART LIST—Model No. WETL30708.0 R0908AKey No. Qty. Description Key No. Qty. Description11Gas Spring265/16" Star Washer32 M10 x 51mm Bolt42M10 W

27Key No. Qty. Description Key No. Qty. Description101 1 Base102 4 Wheel Spacer103 2 Wheel104 1 Key/Clip105 16 8" Wire Tie106 1 Latch Warning Dec

303014554242502951472132531929575659315758651453321942422147512966676433363839197170193644686939383119403330303030303030313128283737106110630114849742

728485813434352283803522278279878889149086141414663383976383877467838609975757575EXPLODED DRAWING B—Model No. WETL30708.0 R0908A29

1. Before beginning this or any exercise pro-gram, consult your physician. This is espe-cially important for persons over age 35 orpersons with pre-ex

1710134141217109594921093411391101721721791297989615541554100161810018100141019791021031059955441212141414161001021021021039101043627188EXPLODED DRAWI

31731041010104552EXPLODED DRAWING D—Model No. WETL30708.0 R0908A

Part No. 266718 R0908A Printed in China © 2008 ICON IP, Inc.ORDERING REPLACEMENT PARTSTo order replacement parts, see the front cover of this manual.

420. Do not attempt to raise, lower, or move thetreadmill until it is properly assembled. (SeeASSEMBLY on page 6, and HOW TO FOLDAND MOVE THE TREADMIL

5Thank you for selecting the new WESLO®COMPACTSL treadmill. The COMPACT SL treadmill offers a selec-tion of features designed to make your workouts at

ASSEMBLYAssembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do notdispose of the packing materials un

71. Make sure that the power cord is unplugged.Orient the Base (101) as shown.Attach four Base Feet (100) to the Base (101) inthe locations shown with

84. With the help of a second person, raise theUprights (96, 98) so the Base (101) is flat on thefloor as shown. Next, position the front of theFrame

96. Hold the remaining Upright Spacer (54) betweenthe Left Upright (96) and the Frame (67) asshown. Attach the Left Upright to the Frame withan M10 x